Soc init failed t17 что это
Перейти к содержимому

Soc init failed t17 что это

  • автор:

ASIC statuses troubleshooting

Reboot is required. Alternatively, you can enable the hashrate-watchdog for automatic reboot.

TUNING

Tuning is in progress, hashrate decrease and software restart are possible.

ERROR_TEMP_TOO_LOW

Too low temperature. Such an error can occur on the Bitmain firmware, and as a result, ASIC stops mining. If you want, you can disable the temperature test on the Hiveon firmware, and continue the mining process.

ERROR_FAN_LOST

Loss of a fan, it is essential to check it. Probably, it is out of order, or there are problems with the sensor.

ERROR_POWER_LOST

Error in setting voltage, error in determining the type of PSU. This could happen due to the following reasons:

  1. Power supply failure.
  2. Excessive decrease in the network — the unit cannot cope with it.
  3. Problems with wiring from the power supply to controller
  4. The new ASIC series can determine the PSU model. If the PSU is worn out, the model may not be identified, and, therefore, the ASIC generates this error.

ERROR_SOC_INIT

Error during the driver initialization. This could happen due to several reasons:

  1. The firmware was installed incorrectly, or the kernel does not match. In this case, you can try to re-flash, install the SD-image, or roll back to another version of the firmware, and then back.
  2. The firmware does not match the model.
  3. Problems with the hardware.

ERROR_EEPROM_INFO

Error when reading the content of EEPROM (wrong format). It is necessary to flash EEPROM.

ERROR_TEMP_LOST

Temperature sensor was lost two or more times. This can happen in case of fail of the chips on which the temperature sensors are located. For example, the 17th model has 4 such chips on every board, and if 2 or more chips fail, it is difficult to determine the temperature, and the mining process stops. To solve the problem, you need to replace the chips.

DISABLED

Hardware defect detected. Mining suspended to keep chips and boards from overheating. To continue mining, manually launch the miner start command.

NOT AVAILABLE (N/A)

The hashrate is currently unavailable. It is possible that an issue has occurred, usually related to a glitchy Internet connection or hashboard malfunctions. If you see red (errors) and orange (warnings) messages, click on them for hints, tips, and troubleshooting methods.

If this status does not change for more than 30 minutes, try rebooting the miner.

Ремонт: Antminer s17/t17

Гость

Официальный сайт | Manual | Прошивка (официальный сайт) | Прошивка (bits.media) В теме действуют все Правила форума! Перед тем как задать вопрос, посмотрите НОВИЧКИ Bits.Media, все сюда, F.A.Q по майнингу. Уважайте своё и чужое время. Для обсуждения и поиска программ/драйверов пользуйтесь разделом Файлы. Сообщения, не относящиеся к теме обсуждения (оффтоп), удаляются без предупреждения. Технические характеристики: Статьи на Bits.me

4 Mar 2020, 20:51 в ASIC/FPGA майнеры

Antminer S17, S17pro, S17+, S17e, T17, T17e, T17+

Официальный сайт | Manual | Прошивка (официальный сайт) | Прошивка (bits.media) В теме действуют все Правила форума! Перед тем как задать вопрос, посмотрите НОВИЧКИ Bits.Media, все сюда, F.A.Q по майнингу. Уважайте своё и чужое время. Для обсуждения и поиска программ/драйверов пользуйтесь разделом Файлы. Сообщения, не относящиеся к теме обсуждения (оффтоп), удаляются без предупреждения. Технические характеристики: Статьи на Bits.me

8 Jun 2019, 07:15 в ASIC/FPGA майнеры

Antminer L3, L3+

Доброй ночи! пожалуйста помогите кто знает с antminer l3+ работает 1.5 недели, все было хорошо. В один момент вижу, что он выключен пришел его перезагрузил и началось Вообщем выдает ошибку socket connect failed. connection refused то иногда включается и показывает на второй плате 21 чип место 71 много раз перезагружал, перекинул с другого асика блок питания он все равно так не майнит уходит в ошибку что делать подскажите пожалуйста, асику всего полторы недели скрины приложил

6 Jun 2017, 22:13 в ASIC/FPGA майнеры

Ремонт innosilicon a4+/a6

Помогите с ремонтом. Долго пытаюсь понять в чем причина. На платах прыгают сигналы en и rst. Соответственно плата не определяется

17 Dec 2021, 00:34 в ASIC/FPGA майнеры

Antminer L7

Доброго дня, уважаемые! Возможно найдётся тот экстремал, кто прикупил данную машину? Отпишитесь по опыту эксплуатации, а то в голову лезет мысль о покупке.

18 Mar 2022, 07:15 в ASIC/FPGA майнеры

  • Ответов 872
  • Создана 23 Nov 2020, 18:49
  • Последний ответ 3 Dec 2022, 10:59

Antminer s19 not working ERROR SOC INIT

Hello my s19 is not working ever since I cleaned it and put it back together. Logs show an error «ERROR_SOC_INIT: soc init failed!». Researching online I’ve found it might be a power supply issue possibly. I’m getting 0 hash power and the hashboards seem to be working fine (logs show it finds 76 asic which is standard for each board) but ends up shutting each board down in the boot process. I’ve tried reconnecting all the wires and hashboards, reverting to factory firmware then updating firmware and still have the same issue. I’m thinking to try flashing with an sd card but I’m not sure if that will really help in my situation. Any help or input is appreciated I’m really not sure where to go from here.

Here is the miner logs the error is towards the bottom:

1970-01-01 00:00:09 Miner compile time: Sat Jul 24 14:04:45 CST 2021 type: Antminer S19a

1970-01-01 00:00:10 This is fix-freq version

1970-01-01 00:00:10 Miner compile time: Sat Jul 24 14:04:45 CST 2021 type: Antminer S19a

1970-01-01 00:00:10 commit version: db12feb 2021-05-12 15:03:10, build by: jenkins 2021-07-24 14:16:14

1970-01-01 00:00:10 opt_multi_version = 1

1970-01-01 00:00:10 opt_bitmain_ab = 1

1970-01-01 00:00:10 mid_auto_gen = 0

1970-01-01 00:00:10 opt_bitmain_work_mode = 0

1970-01-01 00:00:10 mmap fpga_mem_addr_hal = 0xb5900000

1970-01-01 00:00:10 HASH_ON_PLUG V9 = 0xe

1970-01-01 00:00:10 Note: front fan is power on!

1970-01-01 00:00:10 Note: rear fan is power on!

1970-01-01 00:00:10 start the http log.

1970-01-01 00:00:10 httpListenThread start ret=0

1970-01-01 00:00:10 start listen on 6060 .

1970-01-01 00:00:10 load machine BHB28611 conf

1970-01-01 00:00:10 machine : BHB28611

1970-01-01 00:00:10 chain_num 4, chain_domain_num 9, chain_asic_num 72, domain_asic_num 8

1970-01-01 00:00:10 asic 23, wind 0, y 8

1970-01-01 00:00:10 air in

1970-01-01 00:00:10 asic 56, wind 0, y 8

1970-01-01 00:00:10 air in

1970-01-01 00:00:10 asic 16, wind 0, y 1

1970-01-01 00:00:10 air out

1970-01-01 00:00:10 asic 63, wind 0, y 1

1970-01-01 00:00:10 air out

2022-02-24 22:00:00 miner ID : 8044acce7510481c

2022-02-24 22:00:00 FPGA Version = 0xB031

2022-02-24 22:00:00 HASH_ON_PLUG V9 = 0xe

2022-02-24 22:00:00 board num = 3

2022-02-24 22:00:00 board chain num = 1

2022-02-24 22:00:00 chain

2022-02-24 22:00:00 board chain num = 1

2022-02-24 22:00:00 chain

2022-02-24 22:00:00 board chain num = 1

2022-02-24 22:00:00 chain

2022-02-24 22:00:00 chain num = 3

2022-02-24 22:00:02 [chain 1]

2022-02-24 22:00:02 0x0000 11 42 F4 30 1F EA 40 36 98 7D 32 D6 7B 54 C8 8B

2022-02-24 22:00:02 0x0010 27 D4 8C A2 DF 61 6D 0E 03 9A 85 DD 95 FB D4 EE

2022-02-24 22:00:02 0x0020 4F 26 48 37 A0 3A D4 53 A9 C0 2E 78 CB A7 A6 F1

2022-02-24 22:00:02 0x0030 B9 D2 23 A7 7F 07 E9 9D 00 4A F3 03 E6 75 1C 9A

2022-02-24 22:00:02 0x0040 C2 F1 FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:02 0x0050 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:02 0x0060 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:02 0x0070 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:02 0x0080 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:02 0x0090 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:02 0x00A0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:02 0x00B0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:02 0x00C0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:02 0x00D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:02 0x00E0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:02 0x00F0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 5A

2022-02-24 22:00:04 [chain 2]

2022-02-24 22:00:04 0x0000 11 42 11 E5 82 F6 79 15 6A FA 5A ED 1E CA AF 2D

2022-02-24 22:00:04 0x0010 E4 1F 1D BB DC 1B 09 E8 89 FA 46 C3 7C 0B 3D 7D

2022-02-24 22:00:04 0x0020 8D 6F 9C 44 7E 43 4B 5A 72 F0 EF 37 EA E9 33 47

2022-02-24 22:00:04 0x0030 8A A7 FD F7 00 C0 4A 20 E9 FE E8 A1 4E 99 22 8A

2022-02-24 22:00:04 0x0040 5F 19 FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:04 0x0050 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:04 0x0060 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:04 0x0070 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:04 0x0080 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:04 0x0090 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:04 0x00A0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:04 0x00B0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:04 0x00C0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:04 0x00D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:04 0x00E0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:04 0x00F0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 5A

2022-02-24 22:00:06 [chain 3]

2022-02-24 22:00:06 0x0000 11 42 5F DB 6E 25 20 9F C6 23 C3 03 6D A2 35 2F

2022-02-24 22:00:06 0x0010 83 E6 C6 12 40 E2 31 FD DF 19 A9 97 A1 72 4C A5

2022-02-24 22:00:06 0x0020 47 19 25 EE 95 42 02 C6 35 64 0C 49 71 FB D4 DB

2022-02-24 22:00:06 0x0030 AD B6 E4 A7 8E D1 21 1C D2 F6 4B F0 7A 7B 1B B9

2022-02-24 22:00:06 0x0040 2F B3 FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:06 0x0050 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:06 0x0060 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:06 0x0070 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:06 0x0080 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:06 0x0090 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:06 0x00A0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:06 0x00B0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:06 0x00C0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:06 0x00D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:06 0x00E0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

2022-02-24 22:00:06 0x00F0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 5A

2022-02-24 22:00:06 fan_eft : 0 fan_pwm : 100

2022-02-24 22:00:06 create thread

2022-02-24 22:00:06 fixed working voltage = -1

2022-02-24 22:00:06 Chain [1] PCB Version: 0x011e

2022-02-24 22:00:06 Chain [1] BOM Version: 0x0100

2022-02-24 22:00:06 Chain [2] PCB Version: 0x011e

2022-02-24 22:00:06 Chain [2] BOM Version: 0x0100

2022-02-24 22:00:06 Chain [3] PCB Version: 0x011e

2022-02-24 22:00:06 Chain [3] BOM Version: 0x0100

2022-02-24 22:00:10 Fan check passed.

2022-02-24 22:00:10 chain[1] PIC jump to app

2022-02-24 22:00:12 Check chain[1] PIC fw version=0x89

2022-02-24 22:00:13 chain[2] PIC jump to app

2022-02-24 22:00:15 Check chain[2] PIC fw version=0x89

2022-02-24 22:00:16 chain[3] PIC jump to app

2022-02-24 22:00:17 Check chain[3] PIC fw version=0x89

2022-02-24 22:00:18 create thread

2022-02-24 22:00:18 max sensor num = 4

2022-02-24 22:00:18 temperature_monitor_thread start.

2022-02-24 22:00:22 power type version: 0x0071

2022-02-24 22:00:22 Enter sleep to make sure power release finish.

2022-02-24 22:00:53 Slept 30 seconds, diff = 0.

2022-02-24 22:00:53 set_voltage_by_steps to 1500.

2022-02-24 22:00:58 start up min temp by 75a = 255

2022-02-24 22:00:58 set UART baud to 115200

2022-02-24 22:01:00 chain avg vol rise to 15.23

2022-02-24 22:01:06 Chain[1]: find 76 asic, times 0

2022-02-24 22:01:14 Chain[1]: find 76 asic, times 1

2022-02-24 22:01:22 Chain[1]: find 76 asic, times 2

2022-02-24 22:01:22 Chain 1 only find 76 asic, will power off hash board 1

2022-02-24 22:01:25 chain avg vol rise to 22.86

2022-02-24 22:01:30 Chain[2]: find 76 asic, times 0

2022-02-24 22:01:36 chain avg vol drop to 15.21

2022-02-24 22:01:38 Chain[2]: find 76 asic, times 1

2022-02-24 22:01:46 Chain[2]: find 76 asic, times 2

2022-02-24 22:01:46 Chain 2 only find 76 asic, will power off hash board 2

2022-02-24 22:01:48 chain avg vol rise to 30.42

2022-02-24 22:01:54 Chain[3]: find 76 asic, times 0

2022-02-24 22:01:59 chain avg vol drop to 15.21

2022-02-24 22:02:02 Chain[3]: find 76 asic, times 1

2022-02-24 22:02:10 Chain[3]: find 76 asic, times 2

2022-02-24 22:02:11 Chain 3 only find 76 asic, will power off hash board 3

2022-02-24 22:02:11 ERROR_SOC_INIT: soc init failed!

2022-02-24 22:02:11 stop_mining: soc init failed!

2022-02-24 22:02:11 uninit_temp_info

2022-02-24 22:02:11 do not read temp anymore.

2022-02-24 22:02:11 cancel thread

2022-02-24 22:02:11 cancel thread

2022-02-24 22:02:11 ****power off hashboard****

2022-02-24 22:02:11 temp monitor thread exit

2022-02-24 22:02:12 STATUS_OKAY

2022-02-24 22:02:12 set_start_time_point total_tv_start_sys=149 total_tv_end_sys=150

Добавить комментарий

Ваш адрес email не будет опубликован. Обязательные поля помечены *