Perr generation что это в биосе

Google Stress App Test 7200 Seconds

gsat.png [ 3.91 МБ | Просмотров: 1296 ]
СвязОчка с камушком тоже встала на место:
LinX(15000, 25000, 35000, 50000) + OCCT(SSE+Большой+Тяжёлый+Переменный) + Universal2

LinX+OCCT+TM.png [ 445.37 КБ | Просмотров: 1296 ]
Готово! Финальный ночной забег на выносливость на свежей ОС:
Экстрим, 7 циклов
Ну, и немного «цифурок»:

Финальный: DR 4266-15-15-1Т | Aida64 + Cinebench R23 + PhotoWorxx | BIOS Voltage : 1.355VCore, 1.51VDram, 1.32VCCIO, 1.33VCCSA, 0.54V DRAM CTRL REF, ODT(80-40-40)

Теперь спокоен, вроде неплохо вышло, хоть и не дотянул до 33.9ns. Первый раз вижу копию выше записи.
И, как обещал, профиль с настройками, жду того, кто догонит (или вообще сделает 1.504VDram, если это вообще возможно):

[2022/02/06 14:16:59]
Ai Overclock Tuner [Manual]
BCLK Frequency [100.0000]
PCIE Frequency [100.0000]
ASUS MultiCore Enhancement [Enabled – Remove All limits]
SVID Behavior [Best-Case Scenario]
AVX Instruction Core Ratio Negative Offset [0]
CPU Core Ratio [Sync All Cores]
ALL-Core Ratio Limit [52]
BCLK Frequency : DRAM Frequency Ratio [100:133]
DRAM Odd Ratio Mode [Enabled]
DRAM Frequency [DDR4-4266MHz]
Xtreme Tweaking [Disabled]
CPU SVID Support [Auto]
Maximus Tweak [Mode 2]
DRAM CAS# Latency [15]
DRAM RAS# to CAS# Delay [15]
DRAM RAS# ACT Time [32]
DRAM Command Rate [N:1]
N to 1 ratio [1]
DRAM RAS# to RAS# Delay L [6]
DRAM RAS# to RAS# Delay S [4]
DRAM REF Cycle Time [296]
DRAM REF Cycle Time 2 [Auto]
DRAM REF Cycle Time 4 [Auto]
DRAM Refresh Interval [65534]
DRAM WRITE Recovery Time [12]
DRAM READ to PRE Time [6]
DRAM FOUR ACT WIN Time [16]
DRAM WRITE to READ Delay [Auto]
DRAM WRITE to READ Delay L [6]
DRAM WRITE to READ Delay S [2]
DRAM CKE Minimum Pulse Width [0]
DRAM Write Latency [14]
ODT RTT WR (CHA) [80 DRAM Clock]
ODT RTT PARK (CHA) [40 DRAM Clock]
ODT RTT NOM (CHA) [40 DRAM Clock]
ODT RTT WR (CHB) [80 DRAM Clock]
ODT RTT PARK (CHB) [40 DRAM Clock]
ODT RTT NOM (CHB) [40 DRAM Clock]
ODT_READ_DURATION [Auto]
ODT_READ_DELAY [Auto]
ODT_WRITE_DURATION [Auto]
ODT_WRITE_DELAY [Auto]
Data Rising Slope [Auto]
Data Rising Slope Offset [Auto]
Cmd Rising Slope [Auto]
Cmd Rising Slope Offset [Auto]
Ctl Rising Slope [Auto]
Ctl Rising Slope Offset [Auto]
Clk Rising Slope [Auto]
Clk Rising Slope Offset [Auto]
Data Falling Slope [Auto]
Data Falling Slope Offset [Auto]
Cmd Falling Slope [Auto]
Cmd Falling Slope Offset [Auto]
Ctl Falling Slope [Auto]
Ctl Falling Slope Offset [Auto]
Clk Falling Slope [Auto]
Clk Falling Slope Offset [Auto]
DRAM RTL INIT value [65]
DRAM IOL INIT value(CHA) [4]
DRAM IOL INIT value(CHB) [4]
DRAM RTL (CHA DIMM0 Rank0) [57]
DRAM RTL (CHA DIMM0 Rank1) [57]
DRAM RTL (CHA DIMM1 Rank0) [0]
DRAM RTL (CHA DIMM1 Rank1) [0]
DRAM RTL (CHB DIMM0 Rank0) [57]
DRAM RTL (CHB DIMM0 Rank1) [57]
DRAM RTL (CHB DIMM1 Rank0) [0]
DRAM RTL (CHB DIMM1 Rank1) [0]
DRAM IOL (CHA DIMM0 Rank0) [7]
DRAM IOL (CHA DIMM0 Rank1) [7]
DRAM IOL (CHA DIMM1 Rank0) [0]
DRAM IOL (CHA DIMM1 Rank1) [0]
DRAM IOL (CHB DIMM0 Rank0) [7]
DRAM IOL (CHB DIMM0 Rank1) [7]
DRAM IOL (CHB DIMM1 Rank0) [0]
DRAM IOL (CHB DIMM1 Rank1) [0]
CHA IO_Latency_offset [21]
CHB IO_Latency_offset [21]
CHA RFR delay [14]
CHB RFR delay [14]
Early Command Training [Auto]
SenseAmp Offset Training [Enabled]
Early ReadMPR Timing Centering 2D [Enabled]
Read MPR Training [Enabled]
Receive Enable Training [Enabled]
Jedec Write Leveling [Enabled]
LPDDR4 Write DQ DQS Retraining [Enabled]
Early Write Time Centering 2D [Auto]
Early Read Time Centering 2D [Auto]
Write Timing Centering 1D [Enabled]
Write Voltage Centering 1D [Auto]
Read Timing Centering 1D [Auto]
Dimm ODT Training* [Auto]
DIMM RON Training* [Auto]
Write Drive Strength/Equalization 2D* [Auto]
Write Slew Rate Training* [Auto]
Read ODT Training* [Auto]
Read Equalization Training* [Auto]
Read Amplifier Training* [Auto]
Write Timing Centering 2D [Auto]
Read Timing Centering 2D [Auto]
Command Voltage Centering [Enabled]
Write Voltage Centering 2D [Auto]
Read Voltage Centering 2D [Auto]
Late Command Training [Enabled]
Round Trip Latency [Disabled]
Turn Around Timing Training [Disabled]
Rank Margin Tool [Enabled]
Margin Check Limit [Disabled]
Memory Test [Disabled]
DIMM SPD Alias Test [Auto]
Receive Enable Centering 1D [Auto]
Retrain Margin Check [Disabled]
CMD Drive Strength and Tx Equalization [Auto]
CMD Slew Rate Training [Auto]
Write Drive Strength Up/Dn independently [Disabled]
tRDRD_sg_Training [6]
tRDRD_sg_Runtime [6]
tRDRD_dg [4]
tRDWR_sg [10]
tRDWR_dg [10]
tWRWR_sg [6]
tWRWR_dg [4]
tWRRD_sg [26]
tWRRD_dg [22]
tRDRD_dr [5]
tRDRD_dd [0]
tRDWR_dr [10]
tRDWR_dd [0]
tWRWR_dr [7]
tWRWR_dd [0]
tWRRD_dr [5]
tWRRD_dd [0]
TWRPRE [30]
TRDPRE [6]
tREFIX9 [Auto]
OREF_RI [Auto]
TXP [0]
PPD [0]
MRC Fast Boot [Enabled]
Delay after Train [Disabled]
DRAM CLK Period [Auto]
Memory Scrambler [Enabled]
Channel A DIMM Control [Enable both DIMMs]
Channel B DIMM Control [Enable both DIMMs]
Trace Centering [Disabled]
MCH Full Check [Auto]
Mem Over Clock Fail Count [Auto]
Training Profile [Auto]
DLLBwEn [2]
Legacy Mode [Disabled]
SPD Write Disable [TRUE]
XTU Setting [Auto]
Voltage Monitor [Die Sense]
CPU Load-line Calibration [Level 6]
Synch ACDC Loadline with VRM Loadline [Disabled]
CPU Current Capability [140%]
CPU VRM Switching Frequency [Manual]
Fixed CPU VRM Switching Frequency(KHz) [1000KHz]
CPU Power Duty Control [Extreme]
CPU Power Phase Control [Extreme]
CPU Power Thermal Control [130]
CPU VRM Thermal Control [Auto]
DRAM Current Capability [130%]
DRAM Switching Frequency [Manual]
Fixed DRAM Switching Frequency(KHz) [500]
CPU Core/Cache Boot Voltage [Auto]
DMI Boot Voltage [Auto]
CPU System Agent Boot Voltage [Auto]
CPU VCCIO Boot Voltage [Auto]
PLL Termination Boot voltage [Auto]
CPU Standby Boot Voltage [Auto]
Maximum CPU Core Temperature [Auto]
CPU Core/Cache Current Limit Max. [255.75]
Long Duration Package Power Limit [4095]
Package Power Time Window [448]
Short Duration Package Power Limit [4095]
IA AC Load Line [0.01]
IA DC Load Line [0.01]
TVB Voltage Optimizations [Auto]
TVB Ratio Clipping [Auto]
V-Max Stress [Auto]
Offset Mode Sign 1 [+]
V/F Point 1 Offset [Auto]
Offset Mode Sign 2 [+]
V/F Point 2 Offset [Auto]
Offset Mode Sign 3 [+]
V/F Point 3 Offset [Auto]
Offset Mode Sign 4 [+]
V/F Point 4 Offset [Auto]
Offset Mode Sign 5 [+]
V/F Point 5 Offset [Auto]
Offset Mode Sign 6 [+]
V/F Point 6 Offset [Auto]
Offset Mode Sign 7 [+]
V/F Point 7 Offset [Auto]
Offset Mode Sign 8 [+]
V/F Point 8 Offset [Auto]
Realtime Memory Timing [Enabled]
FCLK Frequency for Early Power On [Normal (800Mhz)]
Initial BCLK Frequency [Auto]
BCLK Amplitude [Auto]
BCLK Slew Rate [Auto]
BCLK Spread Spectrum [Disabled]
BCLK Frequency Slew Rate [Auto]
PCIE/DMI Amplitude [Auto]
PCIE/DMI Spread Spectrum [Disabled]
PCIE/DMI Frequency Slew Rate [Auto]
PCIE/DMI Slew Rate [Auto]
Cold Boot PCIE Frequency [Auto]
DRAM VTT Voltage [0.76250]
VPPDDR Voltage [Auto]
DMI Voltage [Auto]
Internal PLL Voltage [Auto]
GT PLL Voltage [Auto]
Ring PLL Voltage [Auto]
System Agent PLL Voltage [Auto]
Memory Controller PLL Voltage [Auto]
CPU Standby Voltage [Auto]
PLL Bandwidth [Auto]
Eventual DRAM Voltage [Auto]
Eventual CPU Standby Voltage [Auto]
Eventual PLL Termination Voltage [Auto]
Eventual CPU VCCIO Voltage [Auto]
Eventual DMI Voltage [Auto]
System Agent Bandgap Workaround [Auto]
Package Temperature Threshold [Auto]
Regulate Frequency by above Threshold [Auto]
Cooler Efficiency Customize [Keep Training]
Cooler Re-evaluation Algorithm [Normal]
Optimism Scale [100]
Ring Down Bin [Disabled]
Min. CPU Cache Ratio [50]
Max CPU Cache Ratio [50]
BCLK Aware Adaptive Voltage [Enabled]
CPU Core/Cache Voltage [Manual Mode]
— CPU Core Voltage Override [1.355]
DRAM Voltage [1.51000]
CPU VCCIO Voltage [1.32000]
CPU System Agent Voltage [1.33000]
PLL Termination Voltage [Auto]
PCH Core Voltage [Auto]
DRAM CTRL REF Voltage on CHA [0.54000]
DRAM CTRL REF Voltage on CHB [0.54000]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL0 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL1 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL2 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL3 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL4 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL5 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL6 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank0 BL7 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL0 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL1 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL2 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL3 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL4 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL5 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL6 [Auto]
DRAM DATA REF Voltage on CHA DIMM0 Rank1 BL7 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL0 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL1 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL2 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL3 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL4 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL5 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL6 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank0 BL7 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL0 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL1 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL2 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL3 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL4 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL5 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL6 [Auto]
DRAM DATA REF Voltage on CHA DIMM1 Rank1 BL7 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL0 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL1 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL2 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL3 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL4 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL5 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL6 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank0 BL7 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL0 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL1 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL2 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL3 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL4 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL5 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL6 [Auto]
DRAM DATA REF Voltage on CHB DIMM0 Rank1 BL7 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL0 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL1 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL2 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL3 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL4 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL5 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL6 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank0 BL7 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL0 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL1 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL2 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL3 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL4 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL5 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL6 [Auto]
DRAM DATA REF Voltage on CHB DIMM1 Rank1 BL7 [Auto]
PCI Express Native Power Management [Disabled]
DMI Link ASPM Control [Disabled]
ASPM [Disabled]
L1 Substates [Disabled]
PCI Express Clock Gating [Enabled]
DMI Link ASPM Control [Disabled]
PEG — ASPM [Disabled]
ASPM L0s [Both Root and Endpoint Ports]
PTID Support [Enabled]
PECI Access Method [Direct I/O]
PCI Express Native Power Management [Disabled]
Native ASPM [Disabled]
Wake System from S5 [Disabled]
ACPI Debug [Disabled]
Low Power S0 Idle Capability [Disabled]
PEP CPU [Enabled]
PEP Graphics [Enabled]
PEP IPU [Enabled]
PEP PEG0 [Enabled]
PEP SATA [Adapter D0/F1]
PEP enumerated SATA ports [Enabled]
PEP PCIe Storage [Disabled]
PEP I2C0 [Enabled]
PEP I2C1 [Enabled]
PEP XHCI [Enabled]
PEP Audio [Enabled]
PEP CSME [Enabled]
PEP LAN(GBE) [Enabled]
Intel Ready Mode Technology [Disabled]
PCI Delay Optimization [Disabled]
MSI enabled [Enabled]
Software Guard Extensions (SGX) [Disabled]
Tcc Offset Time Window [Auto]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetch [Enabled]
Intel (VMX) Virtualization Technology [Disabled]
PECI [Enabled]
Active Processor Cores [All]
Limit CPUID Maximum [Disabled]
Hyper-Threading [Enabled]
Hyper-Threading of Core 0 [Enabled]
Hyper-Threading of Core 1 [Enabled]
Hyper-Threading of Core 2 [Enabled]
Hyper-Threading of Core 3 [Enabled]
Hyper-Threading of Core 4 [Enabled]
Hyper-Threading of Core 5 [Enabled]
Hyper-Threading of Core 6 [Enabled]
Hyper-Threading of Core 7 [Enabled]
Hyper-Threading of Core 8 [Enabled]
Hyper-Threading of Core 9 [Enabled]
MonitorMWait [Enabled]
BIST [Disabled]
AP threads Idle Manner [MWAIT Loop]
AES [Enabled]
Intel Trusted Execution Technology [Disabled]
Boot performance mode [Turbo Performance]
Intel(R) SpeedStep(tm) [Disabled]
Race To Halt (RTH) [Enabled]
Intel(R) Speed Shift Technology [Disabled]
Turbo Mode [Enabled]
CPU C-states [Disabled]
Latency [250]
CFG Lock [Disabled]
Thermal Monitor [Enabled]
Interrupt Redirection Mode Selection [PAIR with Fixed Priority]
Timed MWAIT [Disabled]
Energy Performance Gain [Disabled]
Overclocking Lock [Disabled]
Dual Tau Boost [Disabled]
VT-d [Disabled]
Above 4G Decoding [Disabled]
DDR PowerDown and idle counter [BIOS]
For LPDDR Only: DDR PowerDown and idle counter [BIOS]
REFRESH_2X_MODE [Disabled]
LPDDR Thermal Sensor [Enabled]
SelfRefresh Enable [Enabled]
SelfRefresh IdleTimer [0]
Throttler CKEMin Defeature [Disabled]
Throttler CKEMin Timer [48]
Use user provided power weights, scale factor, and channel power floor values [Disabled]
Lock Thermal Management Registers [Enabled]
Extern Therm Status [Disabled]
Closed Loop Therm Manage [Disabled]
Open Loop Therm Manage [Disabled]
Warm Threshold Ch0 Dimm0 [255]
Warm Threshold Ch0 Dimm1 [255]
Hot Threshold Ch0 Dimm0 [255]
Hot Threshold Ch0 Dimm1 [255]
Warm Threshold Ch1 Dimm0 [255]
Warm Threshold Ch1 Dimm1 [255]
Hot Threshold Ch1 Dimm0 [255]
Hot Threshold Ch1 Dimm1 [255]
Warm Budget Ch0 Dimm0 [255]
Warm Budget Ch0 Dimm1 [255]
Hot Budget Ch0 Dimm0 [255]
Hot Budget Ch0 Dimm1 [255]
Warm Budget Ch1 Dimm0 [255]
Warm Budget Ch1 Dimm1 [255]
Hot Budget Ch1 Dimm0 [255]
Hot Budget Ch1 Dimm1 [255]
RAPL PL Lock [Disabled]
RAPL PL 1 enable [Disabled]
RAPL PL 1 Power [0]
RAPL PL 1 WindowX [0]
RAPL PL 1 WindowY [0]
RAPL PL 2 enable [Disabled]
RAPL PL 2 Power [222]
RAPL PL 2 WindowX [1]
RAPL PL 2 WindowY [10]
Memory Thermal Management [Disabled]
MRC ULT Safe Config [Disabled]
Safe Mode Support [Disabled]
HOB Buffer Size [Auto]
ECC Support [Enabled]
Max TOLUD [Dynamic]
SA GV [Enabled]
SA GV Low Freq [MRC default]
Retrain on Fast Fail [Enabled]
RMT on Fast [Disabled]
BER Support [Enabled]
Enable RH Prevention [Enabled]
Row Hammer Solution [Hardware RHP]
RH Activation Probability [1/2^11]
Exit On Failure (MRC) [Enabled]
Probeless Trace [Disabled]
Memory Trace [Disabled]
GDXC IOT size [4]
GDXC MOT size [12]
Enable/Disable IED (Intel Enhanced Debug) [Disabled]
Ch Hash Support [Enabled]
Ch Hash Mask [0]
Ch Hash Interleaved Bit [BIT8]
Per Bank Refresh [Enabled]
Strong Weak Leaker [7]
Memory Scrambler [Enabled]
Force ColdReset [Disabled]
Force Single Rank [Disabled]
Memory Remap [Enabled]
Time Measure [Disabled]
DLL Weak Lock Support [Enabled]
Pwr Down Idle Timer [0]
MRC Fast Boot [Enabled]
Train On Warm boot [Disabled]
Rank Margin Tool Per Task [Disabled]
Training Tracing [Disabled]
BDAT ACPI Table Support [Disabled]
BDAT Memory Test Type [Rank Margin Tool Rank]
Rank Margin Tool Loop Count [0]
DDR4 Skip Refresh Enable [Enabled]
Primary Display [Auto]
iGPU Multi-Monitor [Disabled]
DMI Max Link Speed [Auto]
Enable Root Port [Auto]
PCIEX16_1 Link Speed [Auto]
Max Link Width [Auto]
Power Down Unused Lanes [Auto]
Gen3 Eq Phase 2 [Auto]
Gen3 Eq Phase 3 Method [Auto]
PEG — ASPM [Disabled]
ASPM L0s [Both Root and Endpoint Ports]
De-emphasis Control [-3.5 dB]
OBFF [Enabled]
LTR [Enabled]
PEG0 Slot Power Limit Value [75]
PEG0 Slot Power Limit Scale [1.0x]
PEG0 Physical Slot Number [1]
PEG0 Hotplug [Disabled]
Enable Root Port [Auto]
PCIEX16_2 Link Speed [Auto]
Max Link Width [Auto]
Power Down Unused Lanes [Auto]
Gen3 Eq Phase 2 [Auto]
Gen3 Eq Phase 3 Method [Auto]
ASPM [Auto]
ASPM L0s [Both Root and Endpoint Ports]
De-emphasis Control [-3.5 dB]
OBFF [Enabled]
LTR [Enabled]
PEG1 Slot Power Limit Value [75]
PEG1 Slot Power Limit Scale [1.0x]
PEG1 Physical Slot Number [2]
PEG1 Hotplug [Disabled]
PCIe Spread Spectrum Clocking [Enabled]
Control Iommu Pre-boot Behavior [Enable IOMMU during boot without exception list]
X2APIC Opt Out [Disabled]
PCIe Speed [Auto]
PCI Express Clock Gating [Enabled]
DMI Link ASPM Control [Disabled]
Port8xh Decode [Disabled]
Port8xh Decode Port# [0]
Peer Memory Write Enable [Disabled]
Compliance Test Mode [Disabled]
PCIe-USB Glitch W/A [Disabled]
PCIe function swap [Enabled]
Number of Coefficients to be used for equalization [3]
RTC Memory Lock [Enabled]
BIOS Lock [Enabled]
Force unlock on all GPIO pads [Disabled]
HD Audio [Enabled]
Audio DSP [Disabled]
Audio Link Mode [HD Audio Link]
HDA-Link Codec Select [Platform Onboard]
iDisplay Audio Disconnect [Disabled]
Codec Sx Wake Capability [Disabled]
PME Enable [Disabled]
HD Audio Link Frequency [24 MHz]
iDisplay Audio Link Frequency [96 MHz]
iDisplay Audio Link T-Mode [2T Mode]
SDCard 3.0 Controller [Disabled]
ISH Controller [Disabled]
Thermal Throttling Level [Suggested Setting]
DMI Thermal Setting [Suggested Setting]
SATA Thermal Setting [Suggested Setting]
Tdispatch []
Tinactive []
Serial IRQ Mode [Quiet]
High Precision Timer [Enabled]
Port 80h Redirection [LPC Bus]
Enhance Port 80h LPC Decoding [Enabled]
Legacy IO Low Latency [Disabled]
PCH Cross Throttling [Enabled]
PCH Energy Reporting [Enabled]
Enable TCO Timer [Disabled]
Pcie Pll SSC [Auto]
IOAPIC 24-119 Entries [Enabled]
Enable 8254 Clock Gate [Enabled]
Flash Protection Range Registers (FPRR) [Disabled]
LGMR [Disabled]
SATA Controller(s) [Enabled]
SATA Mode Selection [AHCI]
Aggressive LPM Support [Disabled]
SMART Self Test [Enabled]
SATA6G_1(Black) [Enabled]
SATA6G_1 Hot Plug [Disabled]
SATA6G_2(Black) [Enabled]
SATA6G_2 Hot Plug [Disabled]
SATA6G_3(Black) [Enabled]
SATA6G_3 Hot Plug [Disabled]
SATA6G_4(Black) [Enabled]
SATA6G_4 Hot Plug [Disabled]
SATA6G_5(Black) [Enabled]
SATA6G_5 Hot Plug [Disabled]
SATA6G_6(Black) [Enabled]
SATA6G_6 Hot Plug [Disabled]
ME State [Enabled]
ME State [Auto]
ME Unconfig on RTC Clear [Enabled]
Comms Hub Support [Disabled]
JHI Support [Disabled]
Extend CSME Measurement to TPM-PCR [Disabled]
Core Bios Done Message [Enabled]
Me FW Image Re-Flash [Disabled]
FW Update [Enabled]
FIPS Mode Select [Disabled]
HECI Timeouts [Enabled]
Force ME DID Init Status [Disabled]
CPU Replaced Polling Disable [Disabled]
ME DID Message [Enabled]
HECI Message check Disable [Disabled]
MBP HOB Skip [Disabled]
HECI2 Interface Communication [Disabled]
KT Device [Enabled]
End Of Post Message [Enabled]
D0I3 Setting for HECI Disable [Disabled]
MCTP Broadcast Cycle [Disabled]
Automatic HW-Enforced Anti-Rollback SVN [Disabled]
Set HW-Enforced Anti-Rollback for Current SVN [Disabled]
PTT [Disable]
DTS SMM [Disabled]
Tcc Activation Offset [0]
Tcc Offset Time Window [Auto]
Tcc Offset Clamp Enable [Disabled]
Tcc Offset Lock Enable [Disabled]
Bi-directional PROCHOT# [Enabled]
Disable PROCHOT# Output [Enabled]
Disable VR Thermal Alert [Disabled]
PROCHOT Response [Disabled]
PROCHOT Lock [Disabled]
ACPI T-States [Disabled]
PECI Reset [Disabled]
PECI C10 Reset [Disabled]
Automatic Thermal Reporting [Disabled]
Critical Trip Point [119 C (POR)]
Active Trip Point 0 [71 C]
Active Trip Point 0 Fan Speed [100]
Active Trip Point 1 [55 C]
Active Trip Point 1 Fan Speed [75]
Passive Trip Point [95 C]
Passive TC1 Value [1]
Passive TC2 Value [5]
Passive TSP Value [10]
Active Trip Points [Enabled]
Passive Trip Points [Disabled]
Critical Trip Points [Enabled]
PCH Temp Read [Enabled]
CPU Energy Read [Enabled]
CPU Temp Read [Enabled]
Alert Enable Lock [Disabled]
CPU Temperature [72]
CPU Fan Speed [65]
Intel(R) Dynamic Tuning [Disabled]
Secondary Configuration Rework Option For TBT [TBT BP Onboard Enable]
UCSI Retry Mechanism [Disabled]
PS2 Keyboard and Mouse [Enabled]
Power Loss Notification Feature [Disabled]
Enable VTIO Support [Disabled]
HID Event Filter Driver [Disabled]
HEBC value [144371]
Pcie Slot 1 to x4 Mode Rework [Disabled]
PCIe x16 slot GSPI0_CLK Rework [Disabled]
PCIe x16 slot GSXDOUT Rework [Disabled]
DGPU Power Enable [Disabled]
System Time and Alarm Source [ACPI Time and Alarm Device]
Intel Trusted Device Setup Boot [Disabled]
Support PEG Bifurcation Card [Disabled]
OverClocking Feature [Disabled]
WDT Enable [Enabled]
End Of Post Message [Enabled]
USB Provisioning of AMT [Disabled]
Secure Erase mode [Simulated]
Force Secure Erase [Disabled]
MEBx hotkey Pressed [Disabled]
MEBx Selection Screen [Disabled]
Unconfigure ME [Disabled]
ICC/OC Watchdog Timer [Disabled]
Discrete Thunderbolt(TM) Support [Disabled]
Kernel Debug Serial Port [Legacy UART]
Platform Debug Consent [Disabled]
USB3 Type-C UFP2DFP Kernel/Platform Debug Support [Disabled]
PCH Trace Hub Enable Mode [Disabled]
CPU Run Control [No Change]
CPU Run Control Lock [Enabled]
Processor trace memory allocation [Disabled]
JTAG C10 Power Gate [Enabled]
Three Strike Counter [Enabled]
CrashLog Feature [Enabled]
CrashLog On All Reset [Disabled]
PMC Debug Message Enable [Disabled]
CPU Wakeup Timer [Enabled]
Delayed Authentication Mode [Disabled]
TPM State [Enabled]
Pending operation [None]
TCM State [Enabled]
Pending operation [None]
Security Device Support [Enable]
SHA-1 PCR Bank [Enabled]
SHA256 PCR Bank [Enabled]
SHA384 PCR Bank [Disabled]
SHA512 PCR Bank [Disabled]
SM3_256 PCR Bank [Disabled]
Pending operation [None]
Platform Hierarchy [Enabled]
Storage Hierarchy [Enabled]
Endorsement Hierarchy [Enabled]
TPM2.0 UEFI Spec Version [TCG_2]
Physical Presence Spec Version [1.3]
Disable Block Sid [Disabled]
Enable ACPI Auto Configuration [Disabled]
Enable Hibernation [Enabled]
ACPI Sleep State [S3 (Suspend to RAM)]
SMART Self Test [Enabled]
Brightness Setting [255]
BIST Enable [Disabled]
PCI Latency Timer [32 PCI Bus Clocks]
PCI-X Latency Timer [64 PCI Bus Clocks]
VGA Palette Snoop [Disabled]
PERR# Generation [Disabled]
SERR# Generation [Disabled]
Above 4G Decoding [Enabled]
SR-IOV Support [Disabled]
BME DMA Mitigation [Disabled]
Don’t Reset VC-TC Mapping [Enabled]
BIOS Hot-Plug Support [Enabled]
PCI Buses Padding [1]
I/O Resources Padding [4 K]
MMIO 32 bit Resources Padding [16 M]
PFMMIO 32 bit Resources Padding [16 M]
PFMMIO 64 bit Resources Padding [Disabled]
Legacy USB Support [Enabled]
USB 2.0 Controller Mode [HiSpeed]
XHCI Legacy Support [Enabled]
XHCI Hand-off [Enabled]
EHCI Hand-off [Disabled]
USB Mass Storage Driver Support [Enabled]
USB transfer time-out [20 sec]
Device reset time-out [20 sec]
Device power-up delay [Auto]
Device power-up delay in seconds [5]
General UDisk 5.00 [Auto]
U32G2_1 [Enabled]
U32G2_2 [Enabled]
U32G2_3 [Enabled]
U32G2_4 [Enabled]
U32G1_7 [Enabled]
U32G1_8 [Enabled]
U32G1_E1 [Enabled]
U32G1_E2 [Enabled]
U32G1_E3 [Enabled]
U32G1_E4 [Enabled]
U32G1_9 [Enabled]
SP_USB11 [Enabled]
U32G2_5 [Enabled]
U32G2_C6 [Enabled]
Network Stack [Disabled]
Hyper M.2X16 [Disabled]
HD Audio [Enabled]
Intel LAN [Enabled]
Intel LAN PXE Option ROM [Disabled]
USB power delivery in Soft Off state (S5) [Enabled]
Connectivity mode (Wi-Fi & Bluetooth) [Enabled]
When system is in working state [All On]
Q-Code LED Function [POST Code Only]
When system is in sleep, hibernate or soft off states [All On]
M.2_1 Configuration [Auto]
DIMM2_1 Configuration [Auto]
DIMM2_2 Configuration [Auto]
U32G2_C6 Type C Power Mode [Auto]
USB3.2_5 Type C Power Mode [Auto]
ASMedia Storage Controller [Enabled]
Windows Hot-plug Notification [Disabled]
ASPM Support [Disabled]
Restore AC Power Loss [Power Off]
Energy Star Ready [Disabled]
ErP Ready [Disabled]
Power On By PCI-E [Disabled]
Power On By RTC [Disabled]
Device [N\A]
Hide Asus Logo [Disabled]
EZ Flash update via Internet [Disabled]
HW Change Show Warning [Disabled]
CPU Temperature [Monitor]
CPU Package Temperature [Monitor]
MotherBoard Temperature [Monitor]
VRM Temperature [Monitor]
Chipset Temperature [Monitor]
T_Sensor Temperature [Monitor]
DIMM.2 Sensor 1 Temperature [Monitor]
DIMM.2 Sensor 2 Temperature [Monitor]
Water In T Sensor Temperature [Monitor]
Water Out T Sensor Temperature [Monitor]
EXT_Sensor1 Temperature [Monitor]
EXT_Sensor2 Temperature [Monitor]
EXT_Sensor3 Temperature [Monitor]
CPU Fan Speed [Monitor]
CPU Optional Fan Speed [Monitor]
Chassis Fan 1 Speed [Monitor]
Chassis Fan 2 Speed [Monitor]
Chassis Fan 3 Speed [Monitor]
W_PUMP+ Speed [Monitor]
AIO PUMP Speed [Monitor]
Extension Fan 1 Speed [Monitor]
Extension Fan 2 Speed [Monitor]
Extension Fan 3 Speed [Monitor]
Extension Fan 4 Speed [Monitor]
Extension Fan 5 Speed [Monitor]
Extension Fan 6 Speed [Monitor]
CPU Core Voltage [Monitor]
12V Voltage [Monitor]
5V Voltage [Monitor]
3.3V Voltage [Monitor]
Flow Rate [Monitor]
AI Cooling [Disabled]
CPU Q-Fan Control [Auto]
CPU Fan Step Up [0 sec]
CPU Fan Step Down [0 sec]
CPU Fan Speed Lower Limit [200 RPM]
CPU Fan Profile [Standard]
Chassis Fan 1 Q-Fan Control [Auto]
Chassis Fan 1 Q-Fan Source [CPU]
Chassis Fan 1 Step Up [0 sec]
Chassis Fan 1 Step Down [0 sec]
Chassis Fan 1 Speed Low Limit [200 RPM]
Chassis Fan 1 Profile [Standard]
Chassis Fan 2 Q-Fan Control [Auto]
Chassis Fan 2 Q-Fan Source [CPU]
Chassis Fan 2 Step Up [0 sec]
Chassis Fan 2 Step Down [0 sec]
Chassis Fan 2 Speed Low Limit [200 RPM]
Chassis Fan 2 Profile [Standard]
Chassis Fan 3 Q-Fan Control [Auto]
Chassis Fan 3 Q-Fan Source [CPU]
Chassis Fan 3 Step Up [0 sec]
Chassis Fan 3 Step Down [0 sec]
Chassis Fan 3 Speed Low Limit [200 RPM]
Chassis Fan 3 Profile [Standard]
Extension Fan 1 Q-Fan Control [Auto]
Extension Fan 1 Q-Fan Source [CPU]
Extension Fan 1 Step Up [0 sec]
Extension Fan 1 Step Down [0 sec]
Extension Fan 1 Speed Low Limit [200 RPM]
Extension Fan 1 Profile [Standard]
Extension Fan 2 Q-Fan Control [Auto]
Extension Fan 2 Q-Fan Source [CPU]
Extension Fan 2 Step Up [0 sec]
Extension Fan 2 Step Down [0 sec]
Extension Fan 2 Speed Low Limit [200 RPM]
Extension Fan 2 Profile [Standard]
Extension Fan 3 Q-Fan Control [Auto]
Extension Fan 3 Q-Fan Source [CPU]
Extension Fan 3 Step Up [0 sec]
Extension Fan 3 Step Down [0 sec]
Extension Fan 3 Speed Low Limit [200 RPM]
Extension Fan 3 Profile [Standard]
Extension Fan 4 Q-Fan Control [Auto]
Extension Fan 4 Q-Fan Source [CPU]
Extension Fan 4 Step Up [0 sec]
Extension Fan 4 Step Down [0 sec]
Extension Fan 4 Speed Low Limit [200 RPM]
Extension Fan 4 Profile [Standard]
Extension Fan 5 Q-Fan Control [Auto]
Extension Fan 5 Q-Fan Source [CPU]
Extension Fan 5 Step Up [0 sec]
Extension Fan 5 Step Down [0 sec]
Extension Fan 5 Speed Low Limit [200 RPM]
Extension Fan 5 Profile [Standard]
Extension Fan 6 Q-Fan Control [Auto]
Extension Fan 6 Q-Fan Source [CPU]
Extension Fan 6 Step Up [0 sec]
Extension Fan 6 Step Down [0 sec]
Extension Fan 6 Speed Low Limit [200 RPM]
Extension Fan 6 Profile [Standard]
WATER PUMP+ Control [Disabled]
AIO PUMP Control [Disabled]
CPU Temperature LED Switch [Enabled]
Launch CSM [Enabled]
Boot Device Control [UEFI and Legacy OPROM]
Boot from Network Devices [Legacy only]
Boot from Storage Devices [Legacy only]
Boot from PCI-E/PCI Expansion Devices [Legacy only]
OS Type [Other OS]
Fast Boot [Enabled]
Next Boot after AC Power Loss [Fast Boot]
Boot Logo Display [Auto]
POST Delay Time [3 sec]
Bootup NumLock State [On]
Wait For ‘F1’ If Error [Enabled]
AMI Native NVMe Driver Support [Enabled]
Option ROM Messages [Force BIOS]
Interrupt 19 Capture [Disabled]
Setup Mode [Advanced Mode]
Boot Sector (MBR/GPT) Recovery Policy [Local User Control]
Next Boot Recovery Action [Skip]
BIOS Image Rollback Support [Enabled]
Flexkey [Reset]
Setup Animator [Disabled]
Profile Name []
Save to Profile [1]
DIMM Slot Number [DIMM_A1]
Download & Install ARMOURY CRATE app [Enabled]

Как всегда, всем
BCLK поднять до 101,7 , станет еще лучше.

_________________
TableDRAMIntel(simple3nov2020+обычная)
bit.ly/3rTIBLv
bit.ly/32WnkTU
Conf tm5(slight+uni@LMHz+extreme)
bit.ly/2Oe8R00
bit.ly/2H9jIZH
bit.ly/2MUvl6n

The list of UEFI feature(Workload Optimized 2)¶

UEFI settings of Workload optimized 2 is as follows. In addition, customers can not change the following settings.

Boot Feature¶

Setting items (key)

Value set as (Default)

Instead of the startup the logo display screen, it is set to display the POST screen.

In order to support an OS other than UEFI-compatible OS, it is the corresponding set to the traditional BIOS using the CSM.

Set the display mode of the option ROM. Force BIOS is selected to use the Option ROM display mode that has been set by the system BIOS.

Set the power-up state of the NUMLOCK key.

If an error occurs, and then force the system to select [Enable] to wait until the key is pressed.

In the setting to perform the notification of the interrupt signal, it is set to take effect if the option ROM is installed on more than one expansion card.

After a failed initial boot, it is set to be able to re-boot the system from the boot device.

This setting is to enable the watchdog timer to restart the system.

The system will control how to shut down when the power button is pressed.

This setting is for the power state at the time of recovery after a power failure. Currently it is set to be able to resume the last of the power state before power loss.

CPU Configuration¶

Setting items (key)

Value set as (Default)

It is the monitoring settings of BIOS to reduce the level of electromagnetic interference.

It is the support setting for the Intel Hyper-Threading technology to improve the performance of the CPU.

Valid setting of the CPU core. In the default setting, it is set “0” in order to enable all of the CPU cores in the system.

It is the setting for the processor that can specify the area and non-area capable of running the application code in memory.

Setting the inventory number (PPIN) control of the protected processor in the system.

It is a setting for read-ahead data and instructions flow from the main memory to the L2 cache and to improve the performance of the CPU.

This setting is for prefetching 128 bytes of cache line as the CPU configuration.

It is a prefetcher setting of the DCU streamer. It prefetches the data stream from the cache memory for the access data and processing the DCU(Data Cache Unit) to speed in order to improve the performance of the CPU.

In order to improve the performance of the network connection and the system, it is a setting for IP prefetcher in the DCU (data cache unit) to prefetch the IP address.

In order to improve the efficiency of the transfer and data access, it is a setting for the Intel DCA (direct cache access) technology.

Based on Intel‘s hyper — threading architecture, each logical processor (thread) is assigned an ID (sensor assistance) of 256 APIC with an 8 — bit bandwidth. The APIC ID extends from 8 bits to 16 bits to provide 512 sensor assistance for each thread to improve CPU performance.

Based on the Intel VT-d, to enable or disable the X2APIC_OPT_OUT Flag on the system.

It is a setting to ensure the security of data utilizing Intel’s AES (Advanced Encryption Standard).

It is a setting in order to use support of Intel Virtualization Technology for support of direct I/O VT-d by reporting I/O device assignment (virtual machine monitor) to VMM via DMAR ACPI table.

Advanced Power Management Configuration ¶

Setting items (key)

Value set as (Default)

It is a setting to support the power-saving mode. Customize the power settings of the system is selected as a default setting.

Configure the settings of the power performance bias adjustment by the BIOS or OS.

It s a setting for the control method or how actively is used the particular hardware-based power management options.

Configure the settings of the power-management features.

CPU P State Control ¶

Setting items (key)

Value set as (Default)

It is a setting that enables a system to adjust the voltage and core frequency of the processor to take advantage of EIST (Enhanced Intel SpeedStep Technology) and automatically reduce power consumption and heat dissipation.

The setting is used in turbo mode in order to enhance the system performance.

This function is to change the P-state Coordination (power-performance state) adjustment type. P — state Coordination is known as SpeedStep for Intel processors. “HW_ALL” to change the P-state Coordination type of the hardware component is selected.

CPU C State Control ¶

Setting items (key)

Value set as (Default)

This setting is to limit the C-state package registration.

It is a setting for the BIOS to enable the report of the CPU C3 state (ACPI C2) to the OS.

It is a setting for the BIOS to enable the report of the CPU C6 state (ACPI C3) to the OS.

CPU T State Control ¶

Setting items (key)

Value set as (Default)

it is a setting to carry out the reduction of CPU power consumption, in order to reduce the clock cycle and voltage of the CPU when it’s in a significantly stopped state.

Chipset Configuration¶

Chipset Configuration ¶

Setting items (key)

Value set as (Default)

It is a setting to always be cleared during the electrical tuning EV_DFX Lock bits that are disposed on the processor.

This item is only displayed.

IOAT Configuration ¶

Setting items (key)

Value set as (Default)

It is a setting to support the Intel I/OAT (I/O Acceleration Technology).

It is a setting that does not support the snoop mode for each CB equipment.

It is possible to violate the strict ordering rules on the PCI bus for transactions when a particular transaction is completed before other transactions that have already been enqueued. It is a setting to enable support for Relaxed Ordering.

Intel VT for Directed I/O (VT-d) ¶

Setting items (key)

Value set as (Default)

It is an Intel virtualization technology setting. It performs Direct I/O VT-d support by reporting I/O device assignment to VMM (virtual machine monitor) via DMAR ACPI table.

It is a setting to enable the access control service.

It is a setting to enable the interrupt remapping in order to improve the performance of the system.

QPI General Configuration ¶

Setting items (key)

Value set as (Default)

It is a setting to choose the frequency for the QPI link connection.

It is a setting to support the Link L0p in order to reduce the power consumption.

It is a setting to support the Link L1 in order to reduce the power consumption.

It is a setting to enable the Cluster-On-Die support, in order to improve the system performance in cloud computing,

It is a setting is to enable the Early Snoop in order to improve the system performance.

Run the Directory mode, to enable the in memory snoop directory.

It is a setting to enable the Isochronous support in order to meet the QoS requirements (Quality of Service).

Memory Configuration ¶

Setting items (key)

Value set as (Default)

It is a setting for applying the POR restrictions on the DDR4 frequency and voltage programming.

It is a setting for the maximum memory frequency of on-board memory module.

It is a setting to enhance the integrity of the system performance and data.

It is a setting to set the base line of the power limit at the time of execution of the DRAM module.

it is a setting to set via the automatic voltage control during an idle state of the CPU, thereby reducing power consumption, in order to improve the reliability of PU.

The 4G address space or more memory that is divided between the 2 sockets is set to be enabled.

It is a setting to support the A7 (addressing) mode in order to improve the memory performance.

Memory RAS Configuration ¶

Setting items (key)

Value set as (Default)

It is a setting to enable the RAS support.

It is a setting to enable support for memory sparing for rank, in order to improve the memory performance.

It is a setting that allows to enable / disable the rank sparing mode.

Patrol scrub is the process that allows the CPU to correct the correctable memory error detected in the memory module and send the correction to the requester (the original source). If this item is enabled, the IO hub is read and if there is no delay due to internal processing, write back 16 K cycles per cache line. With this method, approximately 64 gigabytes of memory behind the IO hub is scrubbed daily.

In this feature, it sets the waiting time of the system before the next patrol scrub is executed.

Demand scrub is a process that enables the CPU to correct correctable memory errors detected in memory modules. If the CPU or I/O issues a demand read command and it is found that the data read from the memory have a correctable error, it corrects the error and sends it to the requester (original source). The memory is updated as well.

It is a setting to support a device tagging.

South Bridge ¶

Setting items (key)

Value set as (Default)

It is a setting to support the legacy USB devices on board.

It is a work-around solution setting for the OS that does not support the XHCI handoff.

It is for operating systems that do not support EHCI handoff. If this item is enabled, EHCI ownership change will be requested by the EHCI driver. Settings are enabled and disabled.

Provides full legacy USB keyboard support for operating systems that do not support legacy USB devices. This setting enables I / O port 60h / 64h emulation support.

It is a setting to enable the USB 3.0 support.

It is a setting to enable the EHCI (Enhanced Host Controller Interface) support of the USB 2.0 connector.

It is a setting to enable the EHCI (Enhanced Host Controller Interface) support of the USB 2.0 connector.